Author |
Topic ![Next Topic Next Topic](images/icon_go_right.gif) |
talbot
United Kingdom
718 Posts |
Posted - 10/05/2012 : 08:25:11
|
I've just treated my fuel tank with Slosh Tank Sealant purchased from Rusterbuster - an excellent product, superb service and very competitively priced. BUT be very careful with masking any threads the stuff will lock them solid. I screwed a scrap fitting into the hole for the tap and eventually had to drill it out. In fairness Rustbuster do tell you to mask threads but be especially careful!
Cheers
Jan T |
|
Dow
United Kingdom
490 Posts |
|
Bob Stringfield
United Kingdom
854 Posts |
Posted - 10/05/2012 : 09:19:59
|
Tank sealants have been used extensively in the classic motorcycle world.
There have lately been reports of problems and, at a recent large classic show, my impression was that many fewer stalls were selling sealants.
Should a tank sealant prove defective, who pays?
Bob. |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Dow
United Kingdom
490 Posts |
Posted - 10/05/2012 : 10:02:58
|
From Rusterbusters:- "We have tested our product over the last two years with up to 100% corn bio ethanol and the product still show no reaction. We are pretty sure that you will not have a problem. The formula has been the same for 15 years so we do not expect older applications to have a problem either.
Unfortunately we do not control the petrol companies but we are pretty confident."
Pretty Sure Pretty Confident ?
Regards David D |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
etlanpa
United Kingdom
560 Posts |
Posted - 10/05/2012 : 10:28:24
|
The POR-15 sealant that Frost sells is ethanol resistant, but like any of these products you must follow the procedure TO THE LETTER!
I also try to use fuel that contains no ethanol - at the moment Super Unleaded from BP, Esso & Texaco doesn't contain any (apart from areas in the south west I believe). |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
John James
United Kingdom
963 Posts |
Posted - 10/05/2012 : 10:30:05
|
There is a good article on Ethanol in the June issue of my bi-monthly (independent of all car clubs) magazine "Totally T-Type 2" http://ttypes.org/ttt2
The article is by Paul Ireland, who has been conducting a number of tests using three “fuels”, BP Ultimate (premium 97 RON) as a control (which is ethanol free in his area), E10 with added water to “wash out” the ethanol and “pure” E10.
Remember, you read it first in TTT 2!
JOHN JAMES http://ttypes.org |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
talbot
United Kingdom
718 Posts |
Posted - 10/05/2012 : 10:32:03
|
What is there to lose? At £25 delivered to my door I am prepared to take the risk of the sealer failing rather than the certainty that the petrol line will be blocked with rust debris.
Cheers
jan T |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Martin Warner
United Kingdom
85 Posts |
Posted - 10/05/2012 : 10:36:09
|
If the sealer fails you will find bits of it all through your fuel system instead of the rust! |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
bahnisch
Australia
674 Posts |
Posted - 10/05/2012 : 11:51:16
|
I have used the sealant in both motor cycle and prewar MG applications with excellent results. Perhaps the fuel down here in Oz is less likely to attack the sealant? |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Terry Andrews
United Kingdom
546 Posts |
Posted - 10/05/2012 : 17:08:52
|
Hi Jan,
On the bottom of a P / L1/ N type tanks there are bosses with an internal thread. Two of these are feeds for main and reserve fuel lines and the third is a drain plug. Are you saying that if you use Rustbuster and seal these bosses with brass blanking plugs they will be glued in and unable to be removed? If this is the case how do they expect you to slosh the tank? If you tape up the tank with say with “gaffer tape” the internal threads will still get “tank slosh” on the internal threads. Am I missing something here???? I ask the question as I have two new tanks I was thinking of coating with “tank slosh”.
Does anyone know if the slosh from Frost, the POR15 has the same issues as the Rustbuster one that Jan used???..... regards….. Terry A
|
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Keith Wallace
United Kingdom
367 Posts |
Posted - 10/05/2012 : 17:22:46
|
Terry, I treated a PB tank with the frost tank sealant, I plugged the holes with wooden dowling, once the sealant started to go off I removed the plugs and was able to reconnect the pipe work without a problem. The tank lasted a about year but was really too far gone with rust to repair.
Keith |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
etlanpa
United Kingdom
560 Posts |
Posted - 10/05/2012 : 18:25:23
|
When you roll the sealant around the tank you need to concentrate on all the seams/welds - on my K tank I didn't get the sealant anywhere near the top filler bosses or fuel feed & Hobson boss. After leaving the tank draining over night I ran a tap up the drain plug thread. |
Edited by - etlanpa on 10/05/2012 18:29:32 |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
talbot
United Kingdom
718 Posts |
Posted - 10/05/2012 : 18:56:53
|
Hi Terry,
That's exactly what happened to me - the brass plugs could have been screwed in with locktite. I suspect that if I had warmed them they would have unscrewed but obviously didn't want to put a flame near a petrol tank. I was recommended the Rustbuster sealer by a friend and he has now told me that I should have plugged all threads with silicon bath sealant the night before. Apparently this can be easilly removed with a pair of snipe nosed pliers once the sealant has set. OK the sealant may not be a long term cure but what's the alternative?
Cheers
Jan |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Bob Stringfield
United Kingdom
854 Posts |
Posted - 10/05/2012 : 23:50:00
|
To say that something is 'resistant' to something else is to use a weasel word.
A paper towel is water-resistant, but not much.
Do be sure to seal carefully the filler cap as well since most sealants will damage paintwork. I was looking today at a motor cycle tank with the beautifully-restored paint ruined by slosh sealant which had leaked under the cap. .
Bob. |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Gerhard Maier
Germany
874 Posts |
Posted - 11/05/2012 : 12:04:25
|
quote: Originally posted by etlanpa on my K tank I didn't get the sealant anywhere near the top filler bosses or fuel feed & Hobson boss.
I think it is useful to identify the type of thinner, which matches the tank sealant, and also to provide a tin of that stuff. (For the sealant I used it was "acetone") At low temperature the sealants sometimes are so stiff, that they refuse to flow easy in all directions, and adding some thinner can make all the difference. Gerhard |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
PaulusPotter
Netherlands
202 Posts |
Posted - 11/05/2012 : 15:52:02
|
Gentlemen,
For my cars i used a tank sealer both tanks did not give any trouble the MGA was done 26 years ago the TC 3 years ago.
By the way Gerhard just for your information several types of sealer are dissolved in a acetone like liquid but mostly this is methyl iso buthyl ketone shortly MIK.
Terry, I took out the plugs after one day without any problem.
Paul |
![Go to Top of Page Go to Top of Page](images/icon_go_up.gif) |
|
Topic ![Next Topic Next Topic](images/icon_go_right.gif) |
|